Sealand HTS Holding Tanks Basic Fittings Manual do Utilizador descarregar pdf

HTS Fittings Installation

for HTS holding tanks

HTS Fittings Installation

for HTS holding tanks

® Registered; ™ Trademark of Dometic Corporation

600346786 01 01/12

® Registered; ™ Trademark of Dometic Corporation

600346786 01 01/12

3-inch cap – inspection port

1. Place cap into 3-inch (76 mm) threaded hole

(g.

) and tighten until hand-tight.

2. Using spanner wrench or large channel

locks, tighten cap until very little or no black

seal is visible above inlet port (g.

3. To remove cap for tank inspection, use

spanner wrench or large channel locks.

3-inch cap – inspection port

1. Place cap into 3-inch (76 mm) threaded hole

(g.

) and tighten until hand-tight.

2. Using spanner wrench or large channel

locks, tighten cap until very little or no black

seal is visible above inlet port (g.

3. To remove cap for tank inspection, use

spanner wrench or large channel locks.

Inlet and discharge elbow ﬁttings

1. Apply threaded plastic pipe sealant around

threads of elbow (g.

2. Tighten elbow into desired tting on tank

(g.

3. To properly position elbow to receive

sanitation hose, turn elbow only in clockwise

direction (g.

). (Turning the elbow in

opposite direction may loosen connection

and cause leakage.)

4. Make sure to connect waste discharge

hose(s) to tting(s) marked as “Waste Only.”

5. When connecting sanitation hose to plastic

elbows, use silicone grease on end of tting

and inside hose end to help make connec-

tion easier and leakproof. Be sure to use two

hose clamps to secure each connection.

Inlet and discharge elbow ﬁttings

1. Apply threaded plastic pipe sealant around

threads of elbow (g.

2. Tighten elbow into desired tting on tank

(g.

3. To properly position elbow to receive

sanitation hose, turn elbow only in clockwise

direction (g.

). (Turning the elbow in

opposite direction may loosen connection

and cause leakage.)

4. Make sure to connect waste discharge

hose(s) to tting(s) marked as “Waste Only.”

5. When connecting sanitation hose to plastic

elbows, use silicone grease on end of tting

and inside hose end to help make connec-

tion easier and leakproof. Be sure to use two

hose clamps to secure each connection.

2 2

4 4

1 1

3 3

IF SEALAND TANK FITTINGS ARE NOT ASSEMBLED TO TANK,

FOLLOW THESE INSTRUCTIONS.

IF SEALAND TANK FITTINGS ARE NOT ASSEMBLED TO TANK,

FOLLOW THESE INSTRUCTIONS.

Refer to SeaLand Holding Tank

System (HTS) owner’s manual for

complete system installation.

Refer to SeaLand Holding Tank

System (HTS) owner’s manual for

complete system installation.

HTS Fittings Installation 1

Resumo do Conteúdo

Página 1 - HTS Fittings Installation

HTS Fittings Installationfor HTS holding tanksHTS Fittings Installationfor HTS holding tanks® Registered; ™ Trademark of Dometic Corporation© Dometic

Comentários a estes Manuais

Sem comentários

Sealand HTS Holding Tanks Basic Fittings Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Acessórios para água Sealand HTS Holding Tanks Basic Fittings. SeaLand HTS Holding Tanks Basic Fittings User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Acessórios para água Sealand HTS Holding Tanks Basic Fittings